Intake Forms for Plumbers: Fixture Assessment, Drain History, and Emergency Classification
A plumbing call that starts with “something’s leaking” and an address tells you almost nothing. You do not know if your tech needs a drain machine or a torch. You do not know if the water is shut off or if it is flooding the basement right now. You do not know if the house was built in 1948 with galvanized steel that crumbles when you look at it, or in 2019 with PEX and push-fit fittings. Without a structured intake, every service call is a guessing game — and guessing costs you time, return trips, and customer trust.
A plumbing intake form is the document that turns a vague phone call into an actionable dispatch. Here is what it should capture, and why each piece matters.
Service Classification: Emergency vs. Scheduled
The single most important question at intake is whether this call needs a truck rolling now or whether it can be scheduled for next week. Getting this wrong in either direction costs you money — dispatching an emergency crew for a dripping faucet wastes labor, and scheduling a burst pipe for Thursday floods a house. Your intake form should present clear categories so dispatch can triage immediately:
- Emergency — immediate dispatch — burst pipe or active flooding, sewage backup into the living space, gas leak or gas smell near plumbing appliances, no water to the entire property, or a water heater leaking significantly. These calls go to the front of the queue. Your intake should flag them visually so they cannot be confused with scheduled work.
- Urgent — same-day or next-day — no hot water (not life-threatening but disruptive), a single toilet out of service in a one-bathroom home, a leak that is contained but active, or a sump pump failure during rain season. These need prompt attention but do not require dropping everything.
- Scheduled repair — dripping faucet, running toilet, slow drain, low water pressure, noisy pipes (water hammer or pipe rattle), or a fixture that works but needs replacement. These can be booked into normal routing without disrupting the day’s schedule.
- New installation — bathroom remodel, kitchen remodel, water heater replacement, water treatment system installation, water softener, whole-house repipe, rough-in plumbing for new construction or an addition. Installation work requires a site visit or detailed measurements before quoting, and the intake should capture enough scope information to determine whether an estimate visit is needed or whether the job can be quoted from the description.
Problem Description: What Is Actually Happening
After classification, your intake form needs to extract the specifics. “The sink is leaking” could mean the faucet drips, the supply line is spraying, or the drain connection is seeping — three completely different repairs requiring different parts and tools. Structured symptom capture eliminates ambiguity:
- Symptom type — leak (visible water where it should not be), clog or slow drain, no hot water, low water pressure, running toilet, dripping faucet, sewer smell, noisy pipes (banging, hammering, whistling), or discolored water. Each symptom points your tech toward a different diagnosis before they arrive.
- Which fixture or area — kitchen sink, bathroom sink, bathtub or shower, toilet, washing machine, dishwasher, water heater, hose bib, main line, or sewer line. If the problem affects multiple fixtures, that changes the diagnosis entirely — multiple slow drains usually means a main line issue, not individual fixture clogs.
- When did it start — a problem that appeared suddenly (yesterday, this morning) suggests a different cause than one that has been worsening over weeks or months. Sudden onset often means a mechanical failure or a blockage. Gradual onset suggests corrosion, mineral buildup, or a deteriorating component.
- Is it getting worse — a slow drain that is getting slower every day is progressing toward a full blockage. A leak that started as a drip and is now a steady stream has a worsening failure. This question helps dispatch gauge urgency beyond the initial classification.
- Recent changes — was any work done on the plumbing recently? Did the customer install a new appliance? Did they have other construction work done? A slow drain that started the week after a kitchen remodel may be a construction debris blockage, not a sewer line problem.
- Has the customer tried anything — this question matters more than most plumbers realize. If a homeowner has poured chemical drain cleaner down a clogged line, your tech needs to know before they open that drain. Products like Drano and Liquid-Plumr contain sodium hydroxide or sulfuric acid that can cause serious chemical burns if they splash during snaking. A clog that has been treated with chemical drain cleaner is a hazmat situation for your technician, and the intake form is where that gets documented.
Water System Information
The property’s water system configuration affects diagnosis, repair approach, and parts selection. A tech who shows up not knowing the water heater type or the water source is a tech who may need a second trip. Capture the system basics at intake:
- Water source — municipal water or private well. Well water introduces variables that city water does not — pressure tanks, well pumps, iron content, hardness levels, and the absence of municipal pressure regulation. A “low pressure” complaint on a well system is a completely different diagnosis than on municipal water.
- Water heater — type (tank gas, tank electric, tankless gas, tankless electric, solar, heat pump), approximate age, and capacity. A 15-year-old gas tank water heater that is not producing hot water is likely a replacement, not a repair. A 3-year-old tankless unit with the same complaint probably has a flow sensor or ignition issue. Knowing the type and age before arrival lets your tech bring the right diagnostic tools and likely replacement parts.
- Water treatment equipment — water softener, whole-house filtration, reverse osmosis system, UV treatment, or iron filter. Treatment equipment affects water chemistry and flow rates. A water softener that is malfunctioning can cause low pressure, hard water damage to fixtures, or salt in the hot water lines. If the customer has treatment equipment, your tech needs to know its location and condition.
- Main shut-off valve location — a surprising number of homeowners do not know where their main water shut-off is. If the call is for an active leak, the first instruction from dispatch should be to shut off the water — and if the customer cannot locate the valve, that changes the urgency. Your intake form should ask this question and document the answer for future service calls at the same address.
- Sump pump — whether the property has one, where it is, and whether it is working. A failed sump pump during wet weather is often called in as a plumbing emergency even though it is technically a drainage issue. Knowing whether one exists and its condition helps dispatch route the call correctly.
- Water pressure — does the customer perceive their pressure as high, normal, or low? Excessively high pressure (above 80 PSI) damages fixtures, causes running toilets, and stresses supply lines. Many homes lack a pressure reducing valve or have one that has failed. Low pressure complaints may indicate a partially closed valve, a failing pressure regulator, corroded galvanized pipes, or a municipal supply issue.
Property Information: What the Building Tells You
The age and construction of a building dictates what your tech will find behind the walls, under the slab, and in the crawl space. A good intake form captures property details that directly affect the plumbing diagnosis and repair approach:
- Year built — this is not trivia. Homes built before the 1960s likely have galvanized steel drain and supply lines that are corroding from the inside out. Every joint is a potential failure point, and disturbing one section of galvanized pipe often causes leaks at adjacent connections. Homes built between 1978 and 1995 may have polybutylene (poly-B) supply lines — a material that is notorious for spontaneous failure at fittings and has been the subject of class-action lawsuits. Very old homes in certain regions may still have lead supply lines or lead solder joints. Your tech needs to know what era of plumbing they are walking into.
- Number of stories and bathrooms — a three-story home with bathrooms on every level has a fundamentally different drain and vent system than a single-story ranch. Multi-story homes have longer drain stacks, more complex venting, and pressure considerations that single-story homes do not. The number of bathrooms indicates system complexity and helps scope the job.
- Basement or crawl space — is the basement finished or unfinished? A leak in a finished basement is water damage to drywall, flooring, and potentially electrical systems. An unfinished basement with exposed pipes is far easier to diagnose and repair. Does the home have a crawl space, and if so, is there adequate access? Some crawl spaces are 18 inches of clearance — barely enough for a person, let alone tools and materials.
- Sewer connection — municipal sewer or septic system. This affects how drain problems are diagnosed and resolved. A main line clog on a sewer-connected home is snaked to the city connection. A main line issue on a septic system may involve the tank, the distribution box, or the drain field — an entirely different scope of work.
- Last plumbing work — when was plumbing work last performed, and what was done? A home that had a full repipe five years ago has different risk factors than one that has had no plumbing work since it was built in 1972. Recent work also establishes whether a current problem might be related to a previous repair.
Estimate, Permits, and Scheduling
The intake form is also where pricing expectations and scheduling logistics get established. Plumbing is one of the few trades where customers routinely expect on-the-spot pricing for work that cannot be accurately scoped until the tech is on site. Your form should set expectations clearly:
- Diagnostic or trip fee — most plumbing companies charge a dispatch or diagnostic fee that covers the tech’s time to arrive, assess the problem, and provide a repair estimate. This fee should be disclosed at intake, not when the tech is standing at the door. Customers who understand the fee structure before booking are far less likely to dispute it on site.
- Not-to-exceed authorization — for repair calls, establish a dollar threshold beyond which the tech must call for additional authorization before proceeding. A customer who approved a $250 faucet repair does not want to discover the tech replaced $800 worth of supply lines without asking. The not-to-exceed figure goes on the intake form so the tech has it before starting work.
- Permit requirements — most homeowners do not know that plumbing work often requires permits. In the majority of jurisdictions, water heater replacement, new fixture installation, sewer line repair or replacement, and any work that alters the existing plumbing layout requires a permit and inspection. Your intake form should flag the work types that typically require permits so the customer is not surprised when the estimate includes permit costs, and so your office can pull the permit before the work begins rather than after.
- Preferred scheduling — morning, afternoon, or specific time window. Whether someone will be home or whether the tech should call on arrival. Whether there are access restrictions (gated community, locked basement, tenant-occupied unit where entry must be coordinated). Scheduling details captured at intake prevent the wasted trip where the tech arrives and cannot access the property.
- Payment terms — residential plumbing is typically COD — payment collected on completion. If your company offers financing for larger jobs (repipes, water heater installations, bathroom remodels), that should be noted at intake so the tech can present those options on site. For commercial accounts, payment terms (net 30, purchase order requirements) should be established before the work is performed, not negotiated after the invoice is sent.
The Intake Form Is Your First Impression
A plumber who asks the right questions before arriving demonstrates competence before touching a wrench. The customer knows you understand their problem, your tech arrives prepared with the right tools and parts, and your office has the documentation to support accurate invoicing and warranty tracking. Every detail captured at intake is a detail that does not need to be chased down later — and in a trade where time is billed by the hour, that efficiency goes straight to the bottom line.
If you run a multi-trade operation that includes plumbing alongside electrical, HVAC, or other service lines, the Trade Services Bundle provides intake forms across 52 service categories, each built with the trade-specific fields that generic forms miss.
Ready to Upgrade Your Intake Process?
Professional fillable PDF forms — instant download, no monthly fees.
Browse All Forms View Bundles